Static is going to take you a bit to understand. In this setup the TC can be setup to provide DHCP to clients connected to it and show those clients. Put the Linksys as the main router and the TC as the WAP in static IP mode. but that will definitely make life harder.Ĭhange the network around. To get more accurate information you need a way to split the network. since as far as the TC is concerned they are all ethernet devices plugged in via ethernet port that your Linksys is plugged into. they join to whichever gives them the best signal.īecause all networking is handled by the TC, it cannot show you direct which ones are connected on the Linksys. The whole idea of a roaming network is that devices are router neutral. I have Fing on my iPad, but it doesn't really map and seems unable to show what's linked to what. ![]() When PeakHour is running constantly this is no problem but it can lead to inaccuracies if it's not running for long periods / during large transfers.I'm fairly confident the Linksys isn't in repeater mode but is in roaming mode. This means they reset to zero after every 4GB of data transferred when this happens, PeakHour can no longer figure out how much data has been transferred since it was last read. This is because the traffic counters in SNMP are only 32bits which mean they only hold a maximum of 4GB. ![]() If it's alot of data (more than a few gigabytes) then it may not be accurate. If its only a small amount of data (few hundred MBs) then PeakHour will still be accurate when its started again. It actually depends on how much data you put through the router whilst PeakHour is not running. There is a certain amount of leeway here as PeakHour will pick up where it left off after restarting. You're right in that the Mac Mini needs to be running for it to measure total usage. If PeakHour is monitoring your Internet router, it will be measuring usage of all devices that use that router to access the Internet. Just a couple of suggestions, hopefully that helps. One more thing: you can use the old Airport Configuration Utility (5.6.x) to observe the signal strength of each wireless client - this can also be helpful in diagnosing WiFi issues. You could also use it to 'tune' the placement of your AE for best performance to try to minimise those dropouts. This would help you diagnose issues during those slow/dropout/loss of connection periods (by observing the drop in performance). If the Internet is slow, it could be caused by one of those devices taking up all the bandwidth - Activity Monitor can't tell you this.īy monitoring the Airport Express as well, you can see how much bandwidth is going over your wireless LAN. This would let you see the Internet usage of all of your devices (ATV1, iPad, Mac) rather than only the Mac. ![]() PeakHour monitors routers and access points to show total overall usage.įor example, you could set up PeakHour to monitor both your Airport Express and your Internet router (assuming your Internet router supports SNMP or UPnP - if its the Airport Express, it should be no problem). Activity Monitor only shows you the network usage of the Mac that you're on. PeakHour gives you a slightly different perspective to Activity Monitor. See the link at the bottom of for more info. To help with this and ensure people don't buy the app and then end up disappointed because it doesn't work, there is a free Compatibility Check tool available as well. I believe this will greatly increase the number of people who can use this app and may be the first app of it's kind on any platform that can monitor bandwidth usage using UPnP.Īs this is so new and comparatively untested aside from my own collection of devices and those of a dozen or so beta testers it would be great if you could post your feedback and experiences here. The previous version only supported SNMP as a means of monitoring but this new version introduces support for UPnP devices as well. The part I need some help with is compatibility. It's a menubar app that displays your network device's upload and download speeds in real-time.ĭetails can be found at the web site here: I'm hoping you can help with testing the version 2.0 of PeakHour, the network bandwidth tool for OS X.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |